Cold cured or cold pour dentures, also known as temporary dentures, do not look very natural, are not very durable, tend to be highly porous and are only used as a temporary expedient until a more permanent solution is found. These types of dentures are inferior and tend to cost much less due to their quick production time (usually minutes) and low cost materials. It is not suggested that a patient wear a cold cured denture for a long period of time, for they are prone to cracks and can break rather easily.
Once the numbness wore off I could not open my mouth fully for days. It took a full week before I was out of severe pain. It honestly felt like she had broken my jaw. I decided to tough it out as I have a phobia of dentists. Once the severe pain was over my jaw was sore for the next two months. I'm fairly certain that isn't the norm for routine extractions.
I saved to get dentures. Went to this company in Virginia Beach. Dentist decided I had 11 good teeth and recommended partials instead. So I went for the partials. First pulled teeth said one had to be surgically removed, but all those teeth were loose so didn't understand. I was then given temporary partials that had to be adjusted many times as they were always in a hurry to get me out so a new person could be seen. Then I got my permanent ones. They allowed 1 adjustment then they charge after that. I had no money for that. So I was left with too tight ones. I said at the time it was too tight but was told they would get looser. They didn't and it hurts bad to try to get them on. Taking them off felt like I was pulling out the real teeth and it hurt a lot.
The fabrication of a set of complete dentures is a challenge for any dentist/denturist. There are many axioms in the production of dentures that must be understood; ignorance of one axiom can lead to failure of the denture. In the vast majority of cases, complete dentures should be comfortable soon after insertion, although almost always at least two adjustment visits are necessary to remove the cause of sore spots. One of the most critical aspects of dentures is that the impression of the denture must be perfectly made and used with perfect technique to make an accurate model of the patient's edentulous (toothless) gums. The dentist or denturist must use a process called border molding to ensure that the denture flanges are properly extended. An array of problems may occur if the final impression of the denture is not made properly. It takes considerable patience and experience for a dentist to know how to make a denture, and for this reason it may be in the patient's best interest to seek a specialist, either a prosthodontist or denturist, to make the denture. A denturist is a trained and licensed professional who sees patients in need of dentures, partials, relines or repairs. A denturist not only takes the impression, but makes the entire denture in his or her own laboratory. The denturist then schedules a date for the delivery of the finished dentures to the patient. A general dentist may do a good job making dentures, but only if he or she is meticulous and experienced. Many dentists no longer make dentures themselves. but instead take an impression of the patients' mouth and then either send the impressions to a dental laboratory, which could be anywhere in the world, or send the patient to a denturist. Once the laboratory receives dental impressions of the patient's mouth, the laboratory creates plaster molds from them. The laboratory uses the molds to create the wax rims used to register the patient's bite. These wax rims are returned to the dentist, who uses them to register the patient's bite. The dentist may assist the patient in choosing the correct size of teeth for the dentures, or simply make the selection himself. Once bite registration is completed and the teeth are selected for the dentures, the wax rim is usually returned to the dental laboratory in order to have the denture teeth set into the wax. Once the teeth are set into the wax rim, the result is a prefinished denture that looks almost like the finished product. This prefinished denture is usually returned to the dentist's office and the patient usually has a chance to approve the setup (for immediate or standard dentures) or to try the denture before it is finished. After approval by the patient, the dentist returns the pre-denture to the laboratory for final processing. The finished denture is then returned to the dentist's office for delivery to the patient.
The Premium Denture is very high in natural appearance. It features enhanced natural appeal, wear and stain resistance, with detailed customization. As with the UltimateFit and EconomyPlus Dentures, the Premium’s extra-high density teeth are first set in wax for you to try in. Changes may be made at that time. After you have approved the look of your Premium Denture, the lab will custom finish your denture in the permanent acrylic base material. This additional customization results in a more natural look.
