DENTURES DO NOT FIT! DO NOT USE AFFORDABLE! #BOYCOTTAFFORDABLEDENTURES. My father went in for dentures, they are so loose he cannot eat healthy. The first time he went back they put a liner in the uppers to make them tighter, he is using a lot of Poligrip on both the uppers and lowers. He had teeth removed from the bottom and they waited for the gums to heal before measuring for dentures. It has been about 3 months and the dentures, especially the bottom are so loose it hurts him to eat because food gets stuck under the dentures. It is funny because on his first visit the Affordable dentist made fun of how loose his upper dentures were (he has had them for 4 years), they were done by a different dentist. On his first visit he was told by the dentist that the Affordable dentures would fit tight, they don't!
A low-cost denture starts at about $300–$500 per denture, or $600–$1,000 for a complete set of upper and lower dentures. These tend to be cold cured dentures, which are considered temporary because of the lower quality materials and streamlined processing methods used in their manufacture. In many cases, there is no opportunity to try them on for fit before they are finished. They also tend to look artificial and not as natural as higher quality, higher priced dentures.
For many years, partial dentures have been used to replace groups of teeth or a few teeth scattered across the lower or upper jaw. There are a variety of removable partial dentures available to patients and each one comes with its own set of benefits and disadvantages. All partial dentures attach to remaining teeth and have a gum–colored portion meant to blend into the existing gum, with prosthetic teeth to replace the missing teeth.
On my 3rd visit back to readjust my partial...I was going to a wedding and the Dr. wanted me to come back in to make sure it fit. The girl who took care of me (short curly auburn/reddish hair said the partial could not be adjust. I told her the Dr. adjusted it last week for me. Then she said: "well, you are just going to have to learn to adjust it yourself at home in a mean, stern voice.
Denture adhesives, also called denture adherents, are creams, powders, wafers or strips that are used to hold dentures firmly in place. The adhesive also helps form a seal that keeps food particles from sticking between the dentures and gums. Adhesive is applied to clean dentures, which are then positioned in the mouth and held in place for a few seconds, according to the manufacturer’s instructions.
Conventional full dentures are used to replace a full set of teeth either on the upper or lower jaw. When all of the patient’s natural teeth have been removed and the gum tissues have healed, conventional full dentures may be placed in the mouth. In between, the patient may be fitted with an immediate denture that can be inserted on the same day the teeth are extracted. Using immediate full dentures is beneficial for the patient because this means that he does not have to go without teeth for a certain period. Readjustment of the dentures will have to be made after several months because the supporting bone will reshape as it heals and this will cause the denture to loosen.
Effervescent cleansers are the most popular immersion cleansers and include alkaline peroxides, perborates and persulphates. Their cleansing action occurs by the formation of small bubbles which displace loosely attached material from the surface of the denture. They are not very effective as cleansers and have a restricted ability to eliminate microbial plaque. Moreover, they are safe for use and do not cause deterioration of the acrylic resin or the metals used in denture construction.[32] Despite this, they are able to cause rapid damage to some short-term soft lining.[36] Discolouration of the acrylic resin to a white denture often occurs, however, this happens because patients do not follow the manufacturer’s instructions and often add very hot water to the cleaning agent.[37][38]
The dentist let the receptionist girl put the goo in the ID that's sets to a clear rubber to cushion between the ID & my newly extracted teeth. It had too much on one side, was crooked in my mouth & at the top on the other side had no cushion lining which caused a bad sore to form almost immediately. After 5 days I couldn't take it anymore. I drove there (55 miles) to get them to redo the lining. The first time it took her all of 5 minutes to do it. I walked in, they were all there... but was informed that they were ‘about' to leave & told I had to come back the next day! No compassion or good customer care for their patients. DO NOT GO HERE!
FRANKLIN, INDIANA -- On June 19 and 20, 2013, I visited Affordable Dentures, Franklin, Indiana, to receive same-day partials. From the clinic published offerings, I selected what is termed "The Premium Package," at a cost of $1780. The Package consists of a set of full or partial dentures, with the promise of being allowed to return at any time during the first year of wear for repair and adjustments. A final set is then placed in the patient's mouth. The words "at any time" echo throughout the clinic as the patients are being fitted for teeth, and again, as they leave: "You may come back any time you need to." That promise turns out to be a lie, particularly for purchasers of The Package.
The process of fabricating a denture usually begins with an initial dental impression of the maxillary and mandibular ridges. Standard impression materials are used during the process. The initial impression is used to create a simple stone model that represents the maxillary and mandibular arches of the patient's mouth. This is not a detailed impression at this stage. Once the initial impression is taken, the stone model is used to create a 'Custom Impression Tray' which is used to take a second and much more detailed and accurate impression of the patient's maxillary and mandibular ridges. Polyvinylsiloxane impression material is one of several very accurate impression materials used when the final impression is taken of the maxillary and mandibular ridges. A wax rim is fabricated to assist the dentist or denturist in establishing the vertical dimension of occlusion. After this, a bite registration is created to marry the position of one arch to the other.
