I have both upper and lower dentures, but the uppers, which are newer, are very white compared to the bottoms. It will cost me a lot (like $500) to replace them, but I want them to match. Can I whiten my dentures?Answer: It is not possible to whiten dentures like natural teeth because dentures are made of plastic. To minimize staining, properly clean your dentures daily to remove food and plaque bacteria. Brushing with a denture brush or soft toothbrush will prevent dentures from becoming permanently stained and will keep your mouth healthy. Moisten the brush and apply a nonabrasive denture paste (regular toothpaste is too abrasive) or use liquid soap. Brush every surface, inside and out, scrubbing gently. A variety of over-the-counter denture-cleanser products may be safely used (by following the manufacturer’s instructions) to remove some stains. You may also consider soaking your dentures in a cup of water with a teaspoon of household bleach, but be sure to rinse them off well before putting them back in your mouth. When cleaning your dentures, be careful not to drop them as they can break. You should clean your dentures over a sink that is filled with water or has a washcloth in place to prevent the dentures from breaking should you drop them while cleaning. More stubborn stains may require removal by your dentist or prosthodontist, a specialist in denture care and maintenance. To locate a prosthodontist near you, visit www.gotoapro.org. Response provided by the American College of Prosthodontists. Back to top
^{Making quality dentures is a blend of science and art. First, an accurate impression (mold) is made of the alveolar ridges on the top and bottom of your mouth. The base of the denture is made from this mold in a dental laboratory. Working together, the dentist and lab technician choose from among many different sizes and shapes of prosthetic teeth to re-create a natural-looking smile. When everyone is satisfied with the result, the temporary dentures are made in permanent form.}
I saved to get dentures. Went to this company in Virginia Beach. Dentist decided I had 11 good teeth and recommended partials instead. So I went for the partials. First pulled teeth said one had to be surgically removed, but all those teeth were loose so didn't understand. I was then given temporary partials that had to be adjusted many times as they were always in a hurry to get me out so a new person could be seen. Then I got my permanent ones. They allowed 1 adjustment then they charge after that. I had no money for that. So I was left with too tight ones. I said at the time it was too tight but was told they would get looser. They didn't and it hurts bad to try to get them on. Taking them off felt like I was pulling out the real teeth and it hurt a lot.
Your dentist or prosthodontist will instruct you as to how long to wear dentures and when to remove them. During the first several days after receiving your denture, you may be asked to wear it all the time, including while you sleep. Although this may be temporarily uncomfortable, it is the quickest way to identify the areas on the denture that may need adjustment. Once adjustments are made, you should remove dentures before going to bed. This allows gum tissues to rest and allows normal stimulation and cleansing by the tongue and saliva. The denture can be put back in the mouth in the morning.
^{The first visit was nice enough. The receptionists were polite even if they didn't seem to have a clue what they were doing. The only bad experience I had was a very rude lady who dealt with the mountains of paperwork I was filling out. You could clearly tell that she hated her job. With that being said you run into unpleasant people every day and unless you are incredibly thin skinned it shouldn't bother you. It was the least of my problems.}
Teeth can fall out for a number of reasons, ranging from genetics to drug abuse. Most commonly, teeth are removed or fall out on their own due to severe tooth decay. Neglect to upkeep oral hygiene or not seeking proper treatment for damaged teeth, can lead to the onset of decay which in turn leads to loss of teeth. Visiting you dentist in 6 month intervals is a good preventive measure to spot any early signs of decay.
The fabrication of a set of complete dentures is a challenge for any dentist/denturist. There are many axioms in the production of dentures that must be understood; ignorance of one axiom can lead to failure of the denture. In the vast majority of cases, complete dentures should be comfortable soon after insertion, although almost always at least two adjustment visits are necessary to remove the cause of sore spots. One of the most critical aspects of dentures is that the impression of the denture must be perfectly made and used with perfect technique to make an accurate model of the patient's edentulous (toothless) gums. The dentist or denturist must use a process called border molding to ensure that the denture flanges are properly extended. An array of problems may occur if the final impression of the denture is not made properly. It takes considerable patience and experience for a dentist to know how to make a denture, and for this reason it may be in the patient's best interest to seek a specialist, either a prosthodontist or denturist, to make the denture. A denturist is a trained and licensed professional who sees patients in need of dentures, partials, relines or repairs. A denturist not only takes the impression, but makes the entire denture in his or her own laboratory. The denturist then schedules a date for the delivery of the finished dentures to the patient. A general dentist may do a good job making dentures, but only if he or she is meticulous and experienced. Many dentists no longer make dentures themselves. but instead take an impression of the patients' mouth and then either send the impressions to a dental laboratory, which could be anywhere in the world, or send the patient to a denturist. Once the laboratory receives dental impressions of the patient's mouth, the laboratory creates plaster molds from them. The laboratory uses the molds to create the wax rims used to register the patient's bite. These wax rims are returned to the dentist, who uses them to register the patient's bite. The dentist may assist the patient in choosing the correct size of teeth for the dentures, or simply make the selection himself. Once bite registration is completed and the teeth are selected for the dentures, the wax rim is usually returned to the dental laboratory in order to have the denture teeth set into the wax. Once the teeth are set into the wax rim, the result is a prefinished denture that looks almost like the finished product. This prefinished denture is usually returned to the dentist's office and the patient usually has a chance to approve the setup (for immediate or standard dentures) or to try the denture before it is finished. After approval by the patient, the dentist returns the pre-denture to the laboratory for final processing. The finished denture is then returned to the dentist's office for delivery to the patient.

Later that afternoon I came back to have 16 teeth extracted. I got to the office and waited about 30 minutes before I was seen. I got to the back and began injections. After this I went to a full blown panic attack and came close to passing out. The one positive is the dentist who was working on me took it in stride. I wasn't treated disrespectfully and after about 30 minutes the panic subsided and she was able to finish my injections and begin pulling teeth. 
Affordable Dentures