Implant placement: The dental implants, which resemble small screws made of titanium, are surgically placed in the jawbone. In effect, a dental implant replaces the tooth's natural root. Each implant is inserted into the gums and jawbone through a small incision. One of the advantages of implant-supported dentures is that fewer implants can be placed than teeth. For complete upper dentures, between six and eight implants are placed. For complete lower dentures, four to five implants are placed. After the implants have been placed, the gums and bone will take three to six months to grown in around the implant, a process called osseointegration.
It is common for patients with traditional dentures to mumble, slur their speech, or make clicking noises when speaking. This is caused by tense facial muscles that are struggling to keep poorly fitting dentures in their proper position. With implant-supported dentures, these problems can be a thing of the past. When the dentures are secured to dental implants that have become fully integrated with your jaw bone, they will not move around or become displaced. This greatly improves a patient's ability to speak clearly.
Dental implants are a permanent alternative to partial dentures and bring additional benefits that dentures cannot provide and will outlast normal dentures even under optimal conditions. Dental implants will actually replace the entire tooth (the tooth root as well as the crown) which eliminates bone deterioration and brings the same strength and durability as your original tooth.
Most partial dentures contain a thin metal framework that is designed to rest close to your gums and allow for a smooth, non-bulky feel. The framework is supported by your natural teeth to provide a reliable, secure appliance that is easy to use. Where teeth are missing, natural-looking replacement teeth are attached to the frame, and gum-colored acrylic is used to make the appliance blend with your mouth. Again, your mouth and your needs are unique, and Dr. Yonan, Scott, Quigley, Fairbanks & Bushnell work with skilled technicians to create a solution that is comfortable and esthetic.
New dentures may feel awkward for a few weeks until you become accustomed to them. The dentures may feel loose while the muscles of your cheek and tongue learn to keep them in place. It is not unusual to experience minor irritation or soreness. You may find that saliva flow temporarily increases. As your mouth becomes accustomed to the dentures, these problems should go away. Follow-up appointments with the dentist are generally needed after a denture is inserted so the fit can be checked and adjusted. If any problem persists, particularly irritation or soreness, be sure to consult your dentist.
If you are suffering from loss of teeth, there is no reason not to talk to your dentist about the installation of dentures. They offer clear benefits and modern dentures are very natural looking and leave you with a smile even a dentist would struggle to tell apart from the real thing. Whether you or someone in your household is in need of complete upper dentures, Carefree Dental can save you money on the procedure, as well as on most dental procedures!
Fifty-four complete-denture wearers were interviewed one year after they had been fitted with the dentures. Their opinions and reactions were noted and the answers given to standard questions were analysed for inter-correlations and for correlations with findings in earlier series of clinical and roentgenological investigations. Most of the patients were satisfied with the fit, aesthetic effect of the denture and ability to chew and speak. Many of the patients reported oral parafunctions. Roughly every fourth patient used sedatives because they felt restless and nervous.
The process starts by taking a series of impressions or molds of the oral tissues that will support the denture. A dental lab will use these impressions to make models of the patient's mouth. The dentist and laboratory technician will then slowly start building the dentures on these models and transferring them to the patient's mouth at each step to ensure proper fit, establish a proper bite, and ensure that the appearance and esthetics of the denture are desirable. The patient will generally need to be seen by the dentist once per week for about 4 to 5 weeks until the denture is complete. The patient will then need to return occasionally during the first month after the denture is delivered to have adjustments made.
The fabrication of a set of complete dentures is a challenge for any dentist/denturist. There are many axioms in the production of dentures that must be understood; ignorance of one axiom can lead to failure of the denture. In the vast majority of cases, complete dentures should be comfortable soon after insertion, although almost always at least two adjustment visits are necessary to remove the cause of sore spots. One of the most critical aspects of dentures is that the impression of the denture must be perfectly made and used with perfect technique to make an accurate model of the patient's edentulous (toothless) gums. The dentist or denturist must use a process called border molding to ensure that the denture flanges are properly extended. An array of problems may occur if the final impression of the denture is not made properly. It takes considerable patience and experience for a dentist to know how to make a denture, and for this reason it may be in the patient's best interest to seek a specialist, either a prosthodontist or denturist, to make the denture. A denturist is a trained and licensed professional who sees patients in need of dentures, partials, relines or repairs. A denturist not only takes the impression, but makes the entire denture in his or her own laboratory. The denturist then schedules a date for the delivery of the finished dentures to the patient. A general dentist may do a good job making dentures, but only if he or she is meticulous and experienced. Many dentists no longer make dentures themselves. but instead take an impression of the patients' mouth and then either send the impressions to a dental laboratory, which could be anywhere in the world, or send the patient to a denturist. Once the laboratory receives dental impressions of the patient's mouth, the laboratory creates plaster molds from them. The laboratory uses the molds to create the wax rims used to register the patient's bite. These wax rims are returned to the dentist, who uses them to register the patient's bite. The dentist may assist the patient in choosing the correct size of teeth for the dentures, or simply make the selection himself. Once bite registration is completed and the teeth are selected for the dentures, the wax rim is usually returned to the dental laboratory in order to have the denture teeth set into the wax. Once the teeth are set into the wax rim, the result is a prefinished denture that looks almost like the finished product. This prefinished denture is usually returned to the dentist's office and the patient usually has a chance to approve the setup (for immediate or standard dentures) or to try the denture before it is finished. After approval by the patient, the dentist returns the pre-denture to the laboratory for final processing. The finished denture is then returned to the dentist's office for delivery to the patient.
The process of fabricating a denture usually begins with an initial dental impression of the maxillary and mandibular ridges. Standard impression materials are used during the process. The initial impression is used to create a simple stone model that represents the maxillary and mandibular arches of the patient's mouth. This is not a detailed impression at this stage. Once the initial impression is taken, the stone model is used to create a 'Custom Impression Tray' which is used to take a second and much more detailed and accurate impression of the patient's maxillary and mandibular ridges. Polyvinylsiloxane impression material is one of several very accurate impression materials used when the final impression is taken of the maxillary and mandibular ridges. A wax rim is fabricated to assist the dentist or denturist in establishing the vertical dimension of occlusion. After this, a bite registration is created to marry the position of one arch to the other.
The Premium Denture is very high in natural appearance. It features enhanced natural appeal, wear and stain resistance, with detailed customization. As with the UltimateFit and EconomyPlus Dentures, the Premium’s extra-high density teeth are first set in wax for you to try in. Changes may be made at that time. After you have approved the look of your Premium Denture, the lab will custom finish your denture in the permanent acrylic base material. This additional customization results in a more natural look.
